Troubleshooting/Support Request Checklist

From RCS Wiki
Revision as of 00:01, 28 August 2019 by SiteAdmin (talk | contribs)
Jump to navigation Jump to search

Support Request Checklist

For Raptor Computing Systems support to accept a request for support, we first require that certain basic diagnostic checks are completed. Please select the general category of problem from the list below to determine the steps you must complete before submitting a support ticket.

Support tickets sent that do not contain the required information will be automatically closed with a redirect to this Wiki page

NOTE: This page is not yet complete. A transition period is in effect. Once this page is complete the warning above will hold true in all cases!

SYMPTOM: System will not power on

Please complete the following procedures. You must include the information gathered from the diagnostic commands below. A separate computer running Linux, along with a DHCP server (which can be run on the Linux system) may be required to complete all of the diagnostic steps.

Does the system attempt to turn on when you press the power button? The orange power status LED on the mainboard will turn green if the system is powering on.
Yes
Does the system turn off again after 10-15 seconds?
Yes
Action: Remove mainboard from case and unplug all adapters, add on cards, and cables except for the PSU and one stick of RAM. Place mainboard on non-conductive, static-free surface and attempt to power on again after BMC startup has completed by carefully bridging pins 1 and 2 (power switch) on the front panel header. Does the system now power on normally?
Yes
Resolution: Customer provided faulty or miswired addon card or cable bundle, or chassis shorted out critical system component(s).
No
Do you see a boot status screen on the VGA or HDMI port?
Yes
Submit Diagnostic Data: Take a photograph of the text on that screen after all activity has stopped for at least 30 seconds. Send the photograph to support@raptorcs.com along with an acknowledgement that you have reached message ID 17 on the troubleshooting guide. Be sure to include your system serial number, located on the ATX power connector, in your correspondence.
No
Action: Remove the HSF and CPU and carefully inspect the CPU socket. Do you see any bent, damaged, loose, or missing pins?
Yes
Resolution: Customer damage to CPU socket. Recommend purchase of replacement mainboard.
No
Action: Reinstall the CPU and HSF. Attempt to power on again by carefully bridging pins 1 and 2 (power switch) on the front panel header. Do you see a boot status screen on the VGA or HDMI port?
Yes
Is the system functional?
Yes
Resolution: Customer originally installed CPU incorrectly. Reinstallation successful.
No
Submit Diagnostic Data: Take a photograph of the text on that screen after all activity has stopped for at least 30 seconds. Send the photograph to support@raptorcs.com along with an acknowledgement that you have reached message ID 23 on the troubleshooting guide. Be sure to include your system serial number, located on the ATX power connector, in your correspondence.
No
Action: Follow the BMC Connection Guide, then continue.
Submit Diagnostic Data: With the system power off, execute the following commands in sequence on the BMC root shell prompt:
obmcutil poweron
Wait for the mainboard to power on
i2cget -y 12 0x31 0x7
i2cget -y 12 0x31 0x18
i2cget -y 12 0x31 0x19
If the mainboard powered off before you could complete the above diagnostic commands, try again until you can complete all three commands while the mainboard is powered on.
Submit the output of the above commands, along with the full output of:
journalctl -xe
to support@raptorcs.com, along with an acknowledgement that you have reached message ID 26 on the troubleshooting guide. Be sure to include your system serial number, located on the ATX power connector, in your correspondence.
No
Action: Verify BMC startup has completed
As indicated in the users guide for your mainboard, there is a BMC boot delay during which the front panel LEDs will flash in a specific pattern. Until this pattern stops, you will not be able to start the system.
Have the front panel lights stopped flashing in the predetermined boot pattern?
Yes
Are the front panel lights connected to the mainboard?
Yes
Have you attempted to power on after the front panel lights have stopped flashing, with no success?
Yes
Action: Remove mainboard from case and unplug all adapters, add on cards, and cables except for the PSU and one stick of RAM. Place mainboard on non-conductive, static-free surface and attempt to power on again after BMC startup has completed by carefully bridging pins 1 and 2 (power switch) on the front panel header. Does the system now attempt to start?
Yes
Resolution: Customer provided faulty or miswired addon card or cable bundle, or chassis shorted out critical system component(s).
No
Action: Replace the PSU and attempt to power on again after BMC startup has completed. Does the system now attempt to start?
Yes
Resolution: Customer provided faulty PSU.
No
Action: Follow the BMC Connection Guide and return here. WIP.
Submit Diagnostic Data: With the system power off, execute the following commands in sequence on the BMC root shell prompt:
obmcutil poweron
i2cget -y 12 0x31 0x7
i2cget -y 12 0x31 0x18
i2cget -y 12 0x31 0x19
Submit the output of the above commands, along with the full output of:
journalctl -xe
to support@raptorcs.com, along with an acknowledgement that you have reached message ID 27 on the troubleshooting guide. Be sure to include your system serial number, located on the ATX power connector, in your correspondence.
No
Resolution: Attempt power on after the front panel lights have stopped flashing, and restart diagnostics from the beginning.
No
Action: Connect the front panel lights.
Return to step "Verify BMC startup has completed"
No
Resolution: Attempt power on after the front panel lights have stopped flashing, and restart diagnostics from the beginning.

My issue is not listed

For sales inquiries, including technical pre-sales questions, please write to sales@raptorcs.com. If you are having a problem with your system that does not fall into the categories listed above, please write to support@raptorcs.com with acknowledgement that you have reached message ID 25 on the troubleshooting guide. Be sure to include your system serial number, located on the ATX power connector, in your correspondence, along with a clear and concise description of the problem.

Sales requests and general support inquiries made under this heading, where the support request falls into any of the listed symptom categories, will be closed automatically with no response. We urge you to follow the diagnostic procedures provided wherever possible to ensure expedient service.

WIP

Retrieved from "https://wiki.raptorcs.com/w/index.php?title=Troubleshooting/Support_Request_Checklist&oldid=2678"