Difference between revisions of "Talos II/Hardware Compatibility List"

From RCS Wiki
Jump to navigation Jump to search
Line 35: Line 35:
 
* '''SuperMicro SC822'''
 
* '''SuperMicro SC822'''
 
** Low speed fans provide insufficient airflow over CPU0, leading to overheating if more than one 4-core CPU is installed.
 
** Low speed fans provide insufficient airflow over CPU0, leading to overheating if more than one 4-core CPU is installed.
 +
 +
* '''Athena Power RM-3U8G1043'''
 +
** Some motherboard standoffs needed to be removed, and others needed additional hight.
 +
**There was no standoff hole for the top right.
 +
**The support beam across the top of the case interferes with CPU2 heatsink, but can be easily removed.
  
 
=== Candidate Cases ===
 
=== Candidate Cases ===

Revision as of 11:46, 9 May 2018

This is a collection of components known to work with the Talos™ II-based solutions. It's maintained by both Raptor CS and community members.

Cases

These cases were successfully used by someone.

  • SuperMicro SC732i-500B
    • Not recommended for 12 core and higher CPUs
  • SuperMicro SC732D4-903B
    • Add-on sound card recommended
    • Add-on USB 2.0 card or USB 3.0 hub recommended
  • SuperMicro SC747TQ-R1400B or SC747TG-R1400B-SQ
    • Hot swap drive capable; SAS recommended
    • Recommended for use with one or more high-end GPUs
    • Listed as EoL by Supermicro, replaced with 1620 versions. Same fan modules and PDU used in newer, higher watt, version. (Robbieab (talk))
  • Thermaltake Core W200
    • Compatible with caveats
      • Talos™ II mainboard will fit in E-ATX compatible side only (when viewed from rear of case, the right side) if the dual system case.
      • Missing standoff holes for the top-left and top-middle positions. (non-essential but ensure proper support when inserting and removing RAM to avoid bending mainboard)
      • Must remove wire-hole rubber grommets present under Talos™ II mainboard on right lower side for proper fit

Known problematic cases

  • Fractal Design Define XL R2
    • Missing standoff holes for the top-left and top-middle positions.
    • Some alternative standoff in at least the top-middle position may be required to prevent too much bending of the motherboard while inserting RAM.
  • BeQuiet Dark Base 900 (Robbieab (talk))
    • Claims to support E-ATX on the BeQuiet website
    • Infographic showing the motherboard space to only be 322mm deep, which is 8.2mm short of the full-size E-ATX.
    • Emailed them for clarification, but no response. Can't confirm either way.
  • SuperMicro SC822
    • Low speed fans provide insufficient airflow over CPU0, leading to overheating if more than one 4-core CPU is installed.
  • Athena Power RM-3U8G1043
    • Some motherboard standoffs needed to be removed, and others needed additional hight.
    • There was no standoff hole for the top right.
    • The support beam across the top of the case interferes with CPU2 heatsink, but can be easily removed.

Candidate Cases

These cases claim E-ATX support and are planned to be used by someone.

  • Nanoxia Deep Silence2 (Sharkcz)
  • Thermal Take Core W100/W200/WP100/WP200 (Robbieab (talk))
    • Heavy, expensive, massive.
    • Similar price point to the Supermicros with high power PSU + fans.
    • Passed over in favour of the SuperMicro SC747TQ-R1400B
  • Lian Li PC-V1000L (Robbieab (talk))
    • Similar price point to the Supermicros with high power PSU.
    • Very "Apple" brushed aluminium aesthetic.
    • Couldn't confirm E-ATX was fullsize.
    • Passed over in favour of the SuperMicro SC747TQ-R1400B
  • Corsair 760T (mosst)
    • Reasonably cheap.
    • Unusually tasteful aesthetics for a consumer/gaming case. Looks like something Aperture Science would come up with.
    • Yet to confirm if E-ATX is fullsize.
  • Bitfenix Aurora (MarcusC)
    • Seems to be missing some standoff holes, modification may be required

Power Supplies

When planning to run with both CPU sockets populated keep in mind that the power-supply should support also 2 8-pin EPS connectors.

  • Seasonic PRIME 1300W
  • Seasonic PRIME Ultra 650W
  • FSP Group Twins ATX 1+1 Dual Module 700W 80 PLUS GOLD Hot Swappable Redundant Digital Power Supply
    • Customer reported good build quality and proper functionality

Memory

The criteria are basically "is it ECC, is it registered, is it NOT LRDIMM"

From the manual:

Total Slots 16 (4 channels per CPU)
Capacity 2TB maximum
Memory Type DDR4 1600/1866/2133/2400/2666
Memory Features ECC
Module Sizes 8GB, 16GB, 32GB, 64GB, 128GB (RDIMM)

Tested memory

Module Validation
Manufacturer Model Size Speed Type ECC Stepping Firmware Source Notes
Pacific Sun X10723042S 8GB DDR4-19200 Registered Yes POWER9 DD2.1 Hostboot cc2d45a Official
Samsung M393A1G40DB0-CPB 8GB DDR4-17000 Registered Yes POWER9 DD2.2 Hostboot 30dfd3b meklort Requires System Package v1.02
Kingston KTH-PL424/16G 16GB DDR4-19200 Registered Yes POWER9 DD2.1 Hostboot cc2d45a Official
Micron MTA18ASF2G72PZ-2G3B1 16GB DDR4-19200 Registered Yes POWER9 DD2.2 Hostboot 28927a7 Official
Micron MTA18ASF2G72PDZ-2G3D1 16GB DDR4-19200 Registered Yes POWER9 DD2.1 Hostboot cc2d45a Official
Samsung M393A4K40BB1-CRC 32GB DDR4-19200 Registered Yes POWER9 DD2.1 Hostboot 1e2221d Official
Samsung M393A2K40BB2-CTD 16GB DDR4-21300 Registered Yes POWER9 DD2.2 Hostboot 0c8fa110 meklort Will run at 2400MT/s with System Package v1.00
Samsung M393A4K40BB2-CTD8Q 32GB DDR4-21333 Registered Yes POWER9 DD2.2 Hostboot 28927a7 luke-jr
Samsung M393A2G40EB2-CTD 16GB PC4-21300V-R Registered Yes POWER9 DD2.2 Hostboot 30dfd3b JSharp Tested extensively with System Package v1.02 but does boot on v1.00, Dual 8-Core POWER9, x8 DIMM Modules (RCS Recommended Slot Configuration)

Known Incompatible Memory

NOTE: Memory may be removed from this table after firmware support has been added, or there may be a fundamental hardware incompatibility. If you have incompatible memory listed in the table below, you may want to bookmark and check this page from time to time to see if a firmware update has resolved the issue.

Module Test Conditions
Manufacturer Model Size Speed Type ECC Stepping Firmware Last Test
Samsung M386A8K40BMB-CRC 64GB DDR4-19200 Registered LRDIMM Yes POWER9 DD2.1 Hostboot 1e2221d 02/14/2018

SAS/SATA Storage Drives

Connected via optional on-board PM8068 controller, or via PCIe controller. NVMe cards are also supported.

Boards with onboard SAS have 1x MiniSAS (or something like that? confirm!) port, and 4x standard SATA-III ports.

PCIe Devices

Storage Controllers

  • LSI 9300 SAS HBAs
  • PM8068-based SAS HBAs
  • Supermicro AOC-SLG3-4E2P 4-port OCuLink adapter

NVMe M.2 Adapters

  • Ableconn PEXM2-SSD M.2 NGFF PCIe SSD to PCI Express 3.0 x4 Host Adapter Card (M.2 to PCIe adapter)

NVMe Storage Drives

  • Samsung 950 PRO (with M.2 to PCIe adapter)
  • Samsung 960 EVO / PRO (with M.2 to PCIe adapter)
  • Intel Optane 900P NVMe XPoint PCIe

Graphics Cards

  • AMD Radeon HD 5850 - Must disable onboard VGA first. Currently has issues with only using 32-bit DMA.
  • AMD Radeon HD 7950 - Must disable onboard VGA first. Currently has issues with only using 32-bit DMA.
  • Radeon R9 290X
  • AMD Radeon Pro WX7100 - Available pre-installed on Talos II workstation, server, and desktop configurations.
  • AMD Radeon Pro WX5100
  • AMD Radeon Pro WX4100 - May need at least linux 4.16 in order to get Xorg to work.

No display? Check out the GPU Troubleshooting page.

Sound Cards

  • Creative Sound Blaster Audigy FX SB1570 PCIe 5.1 Sound Card
  • Creative Sound Blaster X-Fi Xtreme Fidelity PCIe Audio Sound Card (SB0880)
  • AMD Radeon HD 5850 and 7950 (HDMI audio)
  • VANTEC NBA-120U (USB)

...

CAPI Devices

  • Mellanox ConnectX-6 EN 200Gb/s Adapter Card
Retrieved from "https://wiki.raptorcs.com/w/index.php?title=Talos_II/Hardware_Compatibility_List&oldid=976"